Your Source for Premium
Vehicle & Watercraft Covers

• Zippered panels allow access to the door, engine and both side storage areas
• Adjustable front and rear tension panels provide a custom-like fit
• Triple layer polypropylene top panel beads water on contact provides maximum resistance to rainfall and snow
• Heavy duty single layer polypropylene sides
• Prevents mold, mildew and ice buildup
• Vent flaps eliminate wind lofting and inside moisture
• Elastic corners for fast and easy fitting
• Tough interlocking seams
• Free storage bag and tie-down rope included
• 5-year warranty

The length of your vehicle is typically located on a slip of paper inside one of the cabinets or in the owner's manual. If the paper and manual are missing you will need a tape measure and one another person to measure your vehicle.

1. Place one end of the tape measure on the edge of the rear bumper. Have a friend hold the end of the tape measure in place.

2. Place the tape measure on the edge of the opposite bumper.

3. Read the measurement. This is the official length of your vehicle.

Note about roof equipment (i.e. air conditioners) and bumper accessories (i.e. tanks): All of our covers are design with enough extra play to fit over roof equipment (i.e. air conditioners) and bumper accessories (i.e. tanks). The cover will simply sit a little higher on the side of your RV where the roof equipment or bumper accessory is located. You do NOT need to add anything to the measurement of your vehicle.

Note about vehicle lengths that are with two part numbers: If you find that two different part numbers include your exact vehicle length, always choose the smaller of the two part numbers. Otherwise the cover will be too large and will not fit properly.

Warning: Installation is best done with two people. Never install on a windy day or when your vehicle roof is wet or icy. Please take care whenever you are on a ladder or the roof.

To install the cover, proceed as follows:

1. Cover any sharp edges on your vehicle with tape that could wear against your cover. Lower any roof antennas.
2. Unroll the cover next to your travel trailer with the SafeGuard logo on the cover facing the outside and to the front of your vehicle. Unzip the side and rear panels.
3. On smaller trailers your cover can be installed with ladders or by pulling it over the sides with tie ropes. (Be sure not to snag the cover on the top). On larger trailers it’s easiest to install your cover from the roof. Carefully climb up on the roof pulling the cover front with you. Lower the front of your cover down over the front of your trailer then carefully move toward the back pulling the cover and letting it fall down the sides of your trailer. Climb down the rear ladder and locate the ladder cap. (The cap helps keep the top of the ladder from stressing the cover). Fit it over the ladder top and attach it to the rungs with the hook and loop straps. Now pull the back end of the cover down the back of the trailer.
4. Zip all the cover panels closed and pull the elasticized corners down over both bumpers of your trailer.
5. Locate the hook and loop straps on the upper part of the flaps that fold in under the nose of your trailer. Adjust them to fit your cover to the exact length of the nose of your vehicle.
6. Once the length of the nose of the cover is correctly adjusted, locate one of the supplied ropes and the D-rings sewn in along the flaps that fold in under the nose of your trailer. Tighten the rope and tie it off onto the D-rings located opposite each other. Repeat with the lower D-ring.
7. Tie an end of the supplied rope onto one of the D-rings along the bottom hem. Put a small rock in the provided toss bag, close the top and tie the free end of the rope to the bag D-ring. Now toss the bag and rope under your trailer to the D-ring on the opposite side. Take the rope off the bag and, allowing enough to make a knot, cut it off and tie it to the D-ring. Repeat with the other D-rings. To keep the rope ends from fraying you can carefully melt the ends with a match or lighter.
8. Adjust the strap length on the white tension panels across the front and back to fit your trailer. Don’t over tighten—the straps should be snug, not drum tight. To attach the straps into the side-release buckles just insert the clip into the buckle. To release the buckle press the buttons on both sides and pull the clip out of the buckle.

Your cover can be unzipped for access to the passenger side and rear. The panels can be rolled up and held in place with the hook and loop straps toward the top of each panel. A handy storage bag is provided. To fit it in the bag fold your cover and roll the cover tightly rather than stuffing it. Never store a wet cover in the storage bag or confined area as the cover can be damaged by mildew.

Please Note! Your cover is for storage only. Do not attempt to travel with the cover on, or partially on. Contact with hot surfaces such as exhaust systems will damage the cover.

Caution! Always take care when walking on the roof of your RV. SafeGuard Covers and our parent company takes no responsibility for accidents or damage resulting from walking on the roof of the RV. Avoid walking on the cover because you may slip and fall. Whenever possible, use two people to install the cover. Do not attempt to install the cover in windy conditions.

Cleaning Instructions: The cover may be cleaned by spraying with a hose and/or using a solution of mild soap and water, and a soft brush. Don’t use abrasive cleaners or harsh brushes. Rinse with hose and allow to dry completely before folding for storage.

Warranty: If this cover fails due to a defect in workmanship and materials within five (5) years from the date of purchase SafeGuard Covers will repair or replace it free of charge. Trailering or towing your vehicle wheel with your cover on will invalidate the warranty. This warranty gives you specific rights and you may also have other rights which vary from state to state.